Parking Dynamics PD1 Front Parking Sensor gives total Forward Parking Protection

Front parking sensors along with reversing sensors offer you all around protection for your vehicle.  A parking system with the road conditions we have today is almost a necessity due to the smaller parking lots, the size of cars, and the millions of cars that are on the road. 

The streets are busier with individuals, cars, and objects that can be potential hazards for parking cars.  When you have a parking system you don’t have to worry as much about car parking as you have in the past.  Before we launch into a bunch of scenarios for the front parking aid, we will look at how the PD1 Parking Dynamics Universal Parking Sensor works. 

The PD1 is an electromagnetic parking sensor that is a no holes “invisible when fitted” design.  The electromagnetic front parking sensor has been tested to make sure it is safe and easy to park without incurring bumps, scrapes, or tragic accidents.

Learn more about the Parking Dynamics PD1 Front Parking Sensor
 

The forward parking sensor will fit on any type of vehicle from cars, vans, 4×4’s, SUV’s, Motor Homes, and MPV’s.  The front parking sensor will take the guessing out of parking, especially if your vehicle has blind spots.  The PD1 sensors will detect any object from people, curbs, pillars, posts, walls, fences, vehicles, barriers, skips, and garage doors.
 
The front parking aid has a metallic antenna that mounts on the inner side of your bumper.  The forward parking sensor will even mount on a metal bumper, with some modification to the parking sensor.  The mounting ability enables your bumper to remain free of any ugly and visible front parking sensor from the past technology.
 
There are several reasons why you might want the front parking aid on your vehicle.  We have mentioned a few of these reasons above, but now we will get into more depth for the forward parking sensor.  First of all by having the front parking aid and a reversing parking sensor you will gain all around protection. 

Often we believe we don’t need the front parking sensor because we can see in front of us rather well.  However, in most cars you still can’t see the bumper, despite that fact that you can guage it better.  With the forward parking sensor you are able to determine how close to an object you are, rather than guessing.
 

The front parking aid has two zones to tell you how close to any object you are.  The first zone will read between 70 cm and 20 cm from the object.  You will hear a beep beep sound that increases in frequency as you get closer to the object. If the forward parking sensor detects you are too close it will change the sound of the tone.  This will be zone 2 of the front parking sensor.  Zone 2 is a low frequency, constant beep.

Learn more about the Parking Dynamics PD1 Front Parking Sensor
 

The constant beep of the front parking aid means you should stop immediately and reposition the car.  By repositioning the car the front parking sensor will again guide you to better get out of the parking space you are in.
 
For example if you are in a parallel parking space you need to know how close you are as you ease out of the space.  The car sensor in the park is always engaged when the car is placed in reverse.  However, the forward parking sensor needs to be engaged by a button under the steering wheel.  As you ease out of the space you need to know where the bumper is next to the car in front of you.  The front parking aid can help you tell if you will hit the car in front or if you are not too close.
Another time the front parking aid can be of use is in garage parking.  A garage can be one or more cars wide.  The most typical space is set for one car.  If you are like a lot of individuals you probably have a great deal of stuff in your garage along with your car.  To make it easier for the driver to get out parking to one side is more beneficial than trying to get around your stuff and the mirrors on the car.  The forward parking sensor can help you guide the front of the car into the garage space without hitting anything you are storing in the garage.  The front parking aid can also tell you if you are too close to the wall of the garage.
 
Front parking sensors like the PD1 offer help in a number of scenarios.  Have you ever tried to drive out of a narrow driveway with brick planters lining the sides?  The forward parking sensor in this case could tell you if you are too close to turn and help you avoid the planters.
 
Another reason to use front parking aids comes in parking lots.  With the forward parking sensor you will know if you’re too close to a parked car or when parking cars if you are too close to the curb or light post.  The front parking sensor offers certainty over guessing.
 
For a different scenario in a parking lot let’s look at one more example of a use for forward parking sensors.  The sensors will be able to tell you if the vehicle to the right or left is too close to your bumper.  Imagine yourself leaning high over the steering wheel, guessing if you are too close to the car as you try to make the turn out of the space?  I bet you have done that at least once.  With the front parking aid you no longer have to be worried.  You will simple engage the front parking sensor and begin backing out.  If you do get too close the sensors will alert you. 

The PD1 car parking sensor on your vehicle saves you time, headaches, and accident claims.  It will pay for itself in a matter of months when you no longer need to file a claim for a tiny scratch or big accident.

Learn more about the Parking Dynamics PD1 Front Parking Sensor
 

  • Share/Bookmark

September 24, 2008 at 1:56 pm | Car Parking Sensor, Front Parking Sensor, Parking Aids | No comment

Tags: , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/car-parking-sensor/parking-dynamics-pd1-front-parking-sensor-gives-total-forward-parking-protection/trackback/

Volvo Car Reverse Parking Sensor – The Ultimate Front & Rear Volvo Car Parking Sensor

Parking Dynamics PD1 Volvo Parking & Reversing Sensors use a Unique, No Holes Design that is invisible when fitted. No Drill. No Holes. No Damage!

The Volvo Parking Dynamics PD1 Reverse Parking Sensor uses a unique 100% Accurate, Responsive and Reliable Electromagnetic Sensor Technology that makes parking Safer and Easier, preventing Bumps, Scrapes and Nasty Bangs.

This reverse parking sensor technology is available as a Front and Rear reverse parking sensor giving your vehicle all round parking and reversing protection and giving you Total Parking and Reversing Confidence.

A Volvo Reverse Parking sensor that fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs & Motor Homes gives you total flexibility and optimum compatibility. The PD1 Detects all objects including People, Vehicles, Small & High Kerbs, Pillars, Posts, Walls, Fences, Barriers, Garage Doors, Skips, etc.

As recently reported by the insurance industry, 27% of vehicle accidents are now caused by driver error, when parking and reversing! With more cars on the road now than ever before, the Risk is even greater for accidents to occur. The Volvo Parking Dynamics PD1 will give you peace-of-mind and total parking confidence.

Unique Design:

This unique adhesive metallic antenna design mounts discretely on the inner side of your plastic bumper preserving the ‘new factory look’ of your vehicle and maintains the sleek aesthetic lines of today’s prestige vehicles. Far superior in design and performance to the ultrasonic type of sensor that has ugly and visible sensors.

Totally unique in design, the Volvo PD1 reverse parking sensor is a superior alternative to the older ultrasonic type sensor technology that requires you to drill 4 or 6 holes in your bumper, mounting ugly black sensors that then need painting to colour code and match the shade of your bumper… The Parking Dynamics PD1 makes this a thing of the past!

Find out more about the Parking Dynamics PD1 Volvo Reverse Parking Sensor

 Technical Operation:

When reverse gear is selected the small control unit generates a magnetic field and transfers this to the transceiver adhesive strip that is placed on the inner side of and run the length of your bumper. The PD1 Front sensor is activated by a a switch and works in exactly the same way as the PD1 rear reverse sensor.

The magnetic strip then sends out an elliptical magnetic field to cover the full area around your bumper, front, rear and sides. The transceiver strip works by sending and receiving unlike ultrasonic parking and reverse sensors that require 2 types of sensors, one to send and one to receive; if they become dirty the ultrasonic performance can deteriorate.

Mass is then monitored by the control unit by translating this into a voltage. When an object (i.e. people, kerbs, cars, etc) heavier in mass than the magnetic field enters this elliptical zone, an increase in voltage is detected by the control unit and you are then informed by a series of Volvoble tones or display (PD1-Vision only) how close you are to the object. You can then manoeuvre accordingly with plenty of time to react.

User Operation giving Full Bumper Coverage and Early Detection:

Using Electromagnetic Technology, the Volvo PD1 reverse parking sensor will scan the full length of your bumper, from end to end picking up all objects behind your vehicle. The PD1 detects children, people, adults the elderly plus cars, vehicles, small kerbs, walls, barriers, pillars, posts, skips, etc. Whatever is behind you can rest assured the Volvo PD1 will detect this object and alert you to its presence allowing you to react, with time to spare.

When reverse gear is engaged the reverse parking sensor system provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different Volvoble tones (Zones) alerting you of your proximity in relation to surrounding objects!

As you reverse Zone 1 (furthest away from the object) picks up the object first.

Zone 1: 0.8 to 0.5 Metres in length – The 1st tone signals with a slow "be-be-be" sound

Zone 2: 0.5 to 0.25 Metres in length – The 2nd tone is a faster "be-be-be" sound

Zone 3: 0.25 to 0 Metres in length – the 3rd tone is a constant "beeeeeep" sound

 Volvo Parking Dynamics PD1 Advantages Are Clear!

Parking Dynamics PD1 fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs and Motor Homes giving you maximum compatibility, functionality, reliability and high performance accuracy.

The PD1 is flexible and allows you to move the sensor from vehicle to vehicle upon resale, for the minimum cost of a replacement antenna. No bumper adjustments make this ideal for Rental and Leasing companies.

No Visible Parts, Period! The Parking Dynamics PD1 when fitted is a completely discrete and totally invisible. Only you will know it’s fitted. This ensures a no-holes installation, a higher value to your car—and a more desirable car.

Being CAN bus compatible ensures the PD1 integrates seamlessly with both older conventional wiring systems and the latest intelligent (CAN Bus) multiplex wiring systems. Connect the wrong aftermarket reverse parking sensor and it could be costly. Parking Dynamics is the solution to this dilemma!

No-Drill! The PD1 is fitted without drilling your bumper and unlike ultrasonic type parking sensors there are NO ugly sensors to be mounted in your bumper and then painted. No need to match the paint colour.

A Maintenance FREE Front and Rear parking and reverse sensor technology - No Cleaning, No Adjustment and No Painting of sensors or Constant Testing required!

100% accurate, responsive and reliable in all parking situations and weather conditions – Regardless of the conditions: Sun, Rain, Wind, Snow or Hail the PD1 works and gives you accurate feedback in real time, every time.

Volvo Reverse Parking sensors help and result in a major decrease in minor damage collisions caused when parking and reversing. This simple device will pay for itself many times over by reducing the number of small bangs in which you are involved. Completely eliminating the chance of putting your No Claims Bonus at risk!

Find out more about the Parking Dynamics PD1 Volvo Reverse Parking Sensor

 The Volvo Reverse Parking Dynamics PD1 System comprises of the following!

- The Speaker is small and at just 20mm in diameter mounts anywhere inside of the vehicle and can be run to any location. The Volvoble tones that are emitted to alert you of the proximity of surrounding objects can be clearly heard even when mounted at the back of the vehicle close to or behind interior panels.

- The Electronic Control Unit (ECU) is the ‘brain’ of the PD1, and mounts securely using the supplied adhesive strip either inside of the boot or behind the vehicle bumper. The front ECU mounts under the bonnet or inside of the car, typically behind the glove box. Dimensions of this compact rear sensor unit are just (L57mm x H13mm x D33mm) and the front sensor dimensions are (L75mm x H23mm x D40mm)

- The Antenna is a very strong and flexible adhesive metallic tape that mounts behind the bumper. Its 1cm height and 2.7m length gives you flexibility to run over bumper curves and round bumper mouldings and ensures 100% bumper coverage of even the largest vehicle, offering a full, all round protection zone. The antenna can be cut to any length in seconds.

- The Switch included with the PD1-Front only, mounts discretely inside of the vehicle typically under the steering wheel area for easy access. Press the push-button switch to activate the PD1-Front when parking.

- The LED Display included with the PD1-Vision only, mounts discretely on the rear view mirror and gives you visual and Volvoble alerts to inform you of the proximity of surrounding objects. LED Display Dimensions (L90mm x H30mm x D12mm)

 Volvo Reverse Parking Dynamics PD1 Features:

  • 100% Discrete! No visible parts, so only you will know it is fitted.
  • Automatically beeps if you get to close to an object.
  • Detects people, vehicles, small & high kerbs, garage doors, pillars, posts, walls, fences, barriers, skips, etc.
  • Scans & Protects full length of bumper even onto sides unlike ultrasonic’s.
  • Maintenance FREE!
  • No-Drill, No-Damage! Fitted without drilling bumper unlike ultrasonic type parking sensors.
  • 100% accurate, reliable and responsive in all parking situations and weather conditions.
  • No Paint Required! Unlike ultrasonic type sensors.
  • 2.7 Metre Adhesive antenna mounts on inner side of bumper and can be cut to fit any size of bumper.
  • 100% Compatible with both conventional and the latest CAN Bus multiplex wiring systems.
  • 3 Volvoble Tones alert you of your proximity in relation to surrounding objects. PD1 Vision also has a display.
  • Easy 3 wire installation.
  • Compatible with vehicles that have a tow bar fitted or spare wheel fixed to rear door.
  • Fits all vehicles with a plastic bumper including Cars, 4×4, MPV, SUV, Vans, Vehicles, Motor homes.
  • Ideal for Rental and Leasing companies as no bumper adjustments are required.
  • 2 Year Guarantee.
  • High Performance Reverse Parking Sensor, Reverse Sensor, Reversing Sensor, Parking Aid!

Find out more about the Parking Dynamics PD1 Volvo Reverse Parking Sensor

  • Share/Bookmark

September 22, 2008 at 8:08 am | Car Parking Sensor, Front Parking Sensor, Parking Aids, Rear Parking Sensor, Reverse Parking | No comment

Tags: , , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/car-parking-sensor/volvo-car-reverse-parking-sensor-the-ultimate-universal-front-rear-car-parking-sensor/trackback/

Volkswagen Car Reverse Parking Sensor – The Ultimate Front & Rear Volkswagen Car Parking Sensor

Parking Dynamics PD1 Volkswagen Parking & Reversing Sensors use a Unique, No Holes Design that is invisible when fitted. No Drill. No Holes. No Damage!

The Volkswagen Parking Dynamics PD1 Reverse Parking Sensor uses a unique 100% Accurate, Responsive and Reliable Electromagnetic Sensor Technology that makes parking Safer and Easier, preventing Bumps, Scrapes and Nasty Bangs.

This reverse parking sensor technology is available as a Front and Rear reverse parking sensor giving your vehicle all round parking and reversing protection and giving you Total Parking and Reversing Confidence.

A Volkswagen Reverse Parking sensor that fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs & Motor Homes gives you total flexibility and optimum compatibility. The PD1 Detects all objects including People, Vehicles, Small & High Kerbs, Pillars, Posts, Walls, Fences, Barriers, Garage Doors, Skips, etc.

As recently reported by the insurance industry, 27% of vehicle accidents are now caused by driver error, when parking and reversing! With more cars on the road now than ever before, the Risk is even greater for accidents to occur. The Volkswagen Parking Dynamics PD1 will give you peace-of-mind and total parking confidence.

Unique Design:

This unique adhesive metallic antenna design mounts discretely on the inner side of your plastic bumper preserving the ‘new factory look’ of your vehicle and maintains the sleek aesthetic lines of today’s prestige vehicles. Far superior in design and performance to the ultrasonic type of sensor that has ugly and visible sensors.

Totally unique in design, the Volkswagen PD1 reverse parking sensor is a superior alternative to the older ultrasonic type sensor technology that requires you to drill 4 or 6 holes in your bumper, mounting ugly black sensors that then need painting to colour code and match the shade of your bumper… The Parking Dynamics PD1 makes this a thing of the past!

Find out more about the Parking Dynamics PD1 Volkswagen Reverse Parking Sensor

 Technical Operation:

When reverse gear is selected the small control unit generates a magnetic field and transfers this to the transceiver adhesive strip that is placed on the inner side of and run the length of your bumper. The PD1 Front sensor is activated by a a switch and works in exactly the same way as the PD1 rear reverse sensor.

The magnetic strip then sends out an elliptical magnetic field to cover the full area around your bumper, front, rear and sides. The transceiver strip works by sending and receiving unlike ultrasonic parking and reverse sensors that require 2 types of sensors, one to send and one to receive; if they become dirty the ultrasonic performance can deteriorate.

Mass is then monitored by the control unit by translating this into a voltage. When an object (i.e. people, kerbs, cars, etc) heavier in mass than the magnetic field enters this elliptical zone, an increase in voltage is detected by the control unit and you are then informed by a series of Volkswagenble tones or display (PD1-Vision only) how close you are to the object. You can then manoeuvre accordingly with plenty of time to react.

User Operation giving Full Bumper Coverage and Early Detection:

Using Electromagnetic Technology, the Volkswagen PD1 reverse parking sensor will scan the full length of your bumper, from end to end picking up all objects behind your vehicle. The PD1 detects children, people, adults the elderly plus cars, vehicles, small kerbs, walls, barriers, pillars, posts, skips, etc. Whatever is behind you can rest assured the Volkswagen PD1 will detect this object and alert you to its presence allowing you to react, with time to spare.

When reverse gear is engaged the reverse parking sensor system provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different Volkswagenble tones (Zones) alerting you of your proximity in relation to surrounding objects!

As you reverse Zone 1 (furthest away from the object) picks up the object first.

Zone 1: 0.8 to 0.5 Metres in length – The 1st tone signals with a slow "be-be-be" sound

Zone 2: 0.5 to 0.25 Metres in length – The 2nd tone is a faster "be-be-be" sound

Zone 3: 0.25 to 0 Metres in length – the 3rd tone is a constant "beeeeeep" sound

 Volkswagen Parking Dynamics PD1 Advantages Are Clear!

Parking Dynamics PD1 fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs and Motor Homes giving you maximum compatibility, functionality, reliability and high performance accuracy.

The PD1 is flexible and allows you to move the sensor from vehicle to vehicle upon resale, for the minimum cost of a replacement antenna. No bumper adjustments make this ideal for Rental and Leasing companies.

No Visible Parts, Period! The Parking Dynamics PD1 when fitted is a completely discrete and totally invisible. Only you will know it’s fitted. This ensures a no-holes installation, a higher value to your car—and a more desirable car.

Being CAN bus compatible ensures the PD1 integrates seamlessly with both older conventional wiring systems and the latest intelligent (CAN Bus) multiplex wiring systems. Connect the wrong aftermarket reverse parking sensor and it could be costly. Parking Dynamics is the solution to this dilemma!

No-Drill! The PD1 is fitted without drilling your bumper and unlike ultrasonic type parking sensors there are NO ugly sensors to be mounted in your bumper and then painted. No need to match the paint colour.

A Maintenance FREE Front and Rear parking and reverse sensor technology - No Cleaning, No Adjustment and No Painting of sensors or Constant Testing required!

100% accurate, responsive and reliable in all parking situations and weather conditions – Regardless of the conditions: Sun, Rain, Wind, Snow or Hail the PD1 works and gives you accurate feedback in real time, every time.

Volkswagen Reverse Parking sensors help and result in a major decrease in minor damage collisions caused when parking and reversing. This simple device will pay for itself many times over by reducing the number of small bangs in which you are involved. Completely eliminating the chance of putting your No Claims Bonus at risk!

Find out more about the Parking Dynamics PD1 Volkswagen Reverse Parking Sensor

 The Volkswagen Reverse Parking Dynamics PD1 System comprises of the following!

- The Speaker is small and at just 20mm in diameter mounts anywhere inside of the vehicle and can be run to any location. The Volkswagenble tones that are emitted to alert you of the proximity of surrounding objects can be clearly heard even when mounted at the back of the vehicle close to or behind interior panels.

- The Electronic Control Unit (ECU) is the ‘brain’ of the PD1, and mounts securely using the supplied adhesive strip either inside of the boot or behind the vehicle bumper. The front ECU mounts under the bonnet or inside of the car, typically behind the glove box. Dimensions of this compact rear sensor unit are just (L57mm x H13mm x D33mm) and the front sensor dimensions are (L75mm x H23mm x D40mm)

- The Antenna is a very strong and flexible adhesive metallic tape that mounts behind the bumper. Its 1cm height and 2.7m length gives you flexibility to run over bumper curves and round bumper mouldings and ensures 100% bumper coverage of even the largest vehicle, offering a full, all round protection zone. The antenna can be cut to any length in seconds.

- The Switch included with the PD1-Front only, mounts discretely inside of the vehicle typically under the steering wheel area for easy access. Press the push-button switch to activate the PD1-Front when parking.

- The LED Display included with the PD1-Vision only, mounts discretely on the rear view mirror and gives you visual and Volkswagenble alerts to inform you of the proximity of surrounding objects. LED Display Dimensions (L90mm x H30mm x D12mm)

 Volkswagen Reverse Parking Dynamics PD1 Features:

  • 100% Discrete! No visible parts, so only you will know it is fitted.
  • Automatically beeps if you get to close to an object.
  • Detects people, vehicles, small & high kerbs, garage doors, pillars, posts, walls, fences, barriers, skips, etc.
  • Scans & Protects full length of bumper even onto sides unlike ultrasonic’s.
  • Maintenance FREE!
  • No-Drill, No-Damage! Fitted without drilling bumper unlike ultrasonic type parking sensors.
  • 100% accurate, reliable and responsive in all parking situations and weather conditions.
  • No Paint Required! Unlike ultrasonic type sensors.
  • 2.7 Metre Adhesive antenna mounts on inner side of bumper and can be cut to fit any size of bumper.
  • 100% Compatible with both conventional and the latest CAN Bus multiplex wiring systems.
  • 3 Volkswagenble Tones alert you of your proximity in relation to surrounding objects. PD1 Vision also has a display.
  • Easy 3 wire installation.
  • Compatible with vehicles that have a tow bar fitted or spare wheel fixed to rear door.
  • Fits all vehicles with a plastic bumper including Cars, 4×4, MPV, SUV, Vans, Vehicles, Motor homes.
  • Ideal for Rental and Leasing companies as no bumper adjustments are required.
  • 2 Year Guarantee.
  • High Performance Reverse Parking Sensor, Reverse Sensor, Reversing Sensor, Parking Aid!

Find out more about the Parking Dynamics PD1 Volkswagen Reverse Parking Sensor

  • Share/Bookmark

September 22, 2008 at 8:04 am | Car Parking Sensor, Front Parking Sensor, Parking Aids, Rear Parking Sensor, Reverse Parking | No comment

Tags: , , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/car-parking-sensor/volkswagen-car-reverse-parking-sensor-the-ultimate-universal-front-rear-car-parking-sensor/trackback/

Vauxhall Car Reverse Parking Sensor – The Ultimate Front & Rear Vauxhall Car Parking Sensor

Parking Dynamics PD1 Vauxhall Parking & Reversing Sensors use a Unique, No Holes Design that is invisible when fitted. No Drill. No Holes. No Damage!

The Vauxhall Parking Dynamics PD1 Reverse Parking Sensor uses a unique 100% Accurate, Responsive and Reliable Electromagnetic Sensor Technology that makes parking Safer and Easier, preventing Bumps, Scrapes and Nasty Bangs.

This reverse parking sensor technology is available as a Front and Rear reverse parking sensor giving your vehicle all round parking and reversing protection and giving you Total Parking and Reversing Confidence.

A Vauxhall Reverse Parking sensor that fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs & Motor Homes gives you total flexibility and optimum compatibility. The PD1 Detects all objects including People, Vehicles, Small & High Kerbs, Pillars, Posts, Walls, Fences, Barriers, Garage Doors, Skips, etc.

As recently reported by the insurance industry, 27% of vehicle accidents are now caused by driver error, when parking and reversing! With more cars on the road now than ever before, the Risk is even greater for accidents to occur. The Vauxhall Parking Dynamics PD1 will give you peace-of-mind and total parking confidence.

Unique Design:

This unique adhesive metallic antenna design mounts discretely on the inner side of your plastic bumper preserving the ‘new factory look’ of your vehicle and maintains the sleek aesthetic lines of today’s prestige vehicles. Far superior in design and performance to the ultrasonic type of sensor that has ugly and visible sensors.

Totally unique in design, the Vauxhall PD1 reverse parking sensor is a superior alternative to the older ultrasonic type sensor technology that requires you to drill 4 or 6 holes in your bumper, mounting ugly black sensors that then need painting to colour code and match the shade of your bumper… The Parking Dynamics PD1 makes this a thing of the past!

Find out more about the Parking Dynamics PD1 Vauxhall Reverse Parking Sensor

 Technical Operation:

When reverse gear is selected the small control unit generates a magnetic field and transfers this to the transceiver adhesive strip that is placed on the inner side of and run the length of your bumper. The PD1 Front sensor is activated by a a switch and works in exactly the same way as the PD1 rear reverse sensor.

The magnetic strip then sends out an elliptical magnetic field to cover the full area around your bumper, front, rear and sides. The transceiver strip works by sending and receiving unlike ultrasonic parking and reverse sensors that require 2 types of sensors, one to send and one to receive; if they become dirty the ultrasonic performance can deteriorate.

Mass is then monitored by the control unit by translating this into a voltage. When an object (i.e. people, kerbs, cars, etc) heavier in mass than the magnetic field enters this elliptical zone, an increase in voltage is detected by the control unit and you are then informed by a series of Vauxhallble tones or display (PD1-Vision only) how close you are to the object. You can then manoeuvre accordingly with plenty of time to react.

User Operation giving Full Bumper Coverage and Early Detection:

Using Electromagnetic Technology, the Vauxhall PD1 reverse parking sensor will scan the full length of your bumper, from end to end picking up all objects behind your vehicle. The PD1 detects children, people, adults the elderly plus cars, vehicles, small kerbs, walls, barriers, pillars, posts, skips, etc. Whatever is behind you can rest assured the Vauxhall PD1 will detect this object and alert you to its presence allowing you to react, with time to spare.

When reverse gear is engaged the reverse parking sensor system provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different Vauxhallble tones (Zones) alerting you of your proximity in relation to surrounding objects!

As you reverse Zone 1 (furthest away from the object) picks up the object first.

Zone 1: 0.8 to 0.5 Metres in length – The 1st tone signals with a slow "be-be-be" sound

Zone 2: 0.5 to 0.25 Metres in length – The 2nd tone is a faster "be-be-be" sound

Zone 3: 0.25 to 0 Metres in length – the 3rd tone is a constant "beeeeeep" sound

 Vauxhall Parking Dynamics PD1 Advantages Are Clear!

Parking Dynamics PD1 fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs and Motor Homes giving you maximum compatibility, functionality, reliability and high performance accuracy.

The PD1 is flexible and allows you to move the sensor from vehicle to vehicle upon resale, for the minimum cost of a replacement antenna. No bumper adjustments make this ideal for Rental and Leasing companies.

No Visible Parts, Period! The Parking Dynamics PD1 when fitted is a completely discrete and totally invisible. Only you will know it’s fitted. This ensures a no-holes installation, a higher value to your car—and a more desirable car.

Being CAN bus compatible ensures the PD1 integrates seamlessly with both older conventional wiring systems and the latest intelligent (CAN Bus) multiplex wiring systems. Connect the wrong aftermarket reverse parking sensor and it could be costly. Parking Dynamics is the solution to this dilemma!

No-Drill! The PD1 is fitted without drilling your bumper and unlike ultrasonic type parking sensors there are NO ugly sensors to be mounted in your bumper and then painted. No need to match the paint colour.

A Maintenance FREE Front and Rear parking and reverse sensor technology - No Cleaning, No Adjustment and No Painting of sensors or Constant Testing required!

100% accurate, responsive and reliable in all parking situations and weather conditions – Regardless of the conditions: Sun, Rain, Wind, Snow or Hail the PD1 works and gives you accurate feedback in real time, every time.

Vauxhall Reverse Parking sensors help and result in a major decrease in minor damage collisions caused when parking and reversing. This simple device will pay for itself many times over by reducing the number of small bangs in which you are involved. Completely eliminating the chance of putting your No Claims Bonus at risk!

Find out more about the Parking Dynamics PD1 Vauxhall Reverse Parking Sensor

 The Vauxhall Reverse Parking Dynamics PD1 System comprises of the following!

- The Speaker is small and at just 20mm in diameter mounts anywhere inside of the vehicle and can be run to any location. The Vauxhallble tones that are emitted to alert you of the proximity of surrounding objects can be clearly heard even when mounted at the back of the vehicle close to or behind interior panels.

- The Electronic Control Unit (ECU) is the ‘brain’ of the PD1, and mounts securely using the supplied adhesive strip either inside of the boot or behind the vehicle bumper. The front ECU mounts under the bonnet or inside of the car, typically behind the glove box. Dimensions of this compact rear sensor unit are just (L57mm x H13mm x D33mm) and the front sensor dimensions are (L75mm x H23mm x D40mm)

- The Antenna is a very strong and flexible adhesive metallic tape that mounts behind the bumper. Its 1cm height and 2.7m length gives you flexibility to run over bumper curves and round bumper mouldings and ensures 100% bumper coverage of even the largest vehicle, offering a full, all round protection zone. The antenna can be cut to any length in seconds.

- The Switch included with the PD1-Front only, mounts discretely inside of the vehicle typically under the steering wheel area for easy access. Press the push-button switch to activate the PD1-Front when parking.

- The LED Display included with the PD1-Vision only, mounts discretely on the rear view mirror and gives you visual and Vauxhallble alerts to inform you of the proximity of surrounding objects. LED Display Dimensions (L90mm x H30mm x D12mm)

 Vauxhall Reverse Parking Dynamics PD1 Features:

  • 100% Discrete! No visible parts, so only you will know it is fitted.
  • Automatically beeps if you get to close to an object.
  • Detects people, vehicles, small & high kerbs, garage doors, pillars, posts, walls, fences, barriers, skips, etc.
  • Scans & Protects full length of bumper even onto sides unlike ultrasonic’s.
  • Maintenance FREE!
  • No-Drill, No-Damage! Fitted without drilling bumper unlike ultrasonic type parking sensors.
  • 100% accurate, reliable and responsive in all parking situations and weather conditions.
  • No Paint Required! Unlike ultrasonic type sensors.
  • 2.7 Metre Adhesive antenna mounts on inner side of bumper and can be cut to fit any size of bumper.
  • 100% Compatible with both conventional and the latest CAN Bus multiplex wiring systems.
  • 3 Vauxhallble Tones alert you of your proximity in relation to surrounding objects. PD1 Vision also has a display.
  • Easy 3 wire installation.
  • Compatible with vehicles that have a tow bar fitted or spare wheel fixed to rear door.
  • Fits all vehicles with a plastic bumper including Cars, 4×4, MPV, SUV, Vans, Vehicles, Motor homes.
  • Ideal for Rental and Leasing companies as no bumper adjustments are required.
  • 2 Year Guarantee.
  • High Performance Reverse Parking Sensor, Reverse Sensor, Reversing Sensor, Parking Aid!

Find out more about the Parking Dynamics PD1 Vauxhall Reverse Parking Sensor

  • Share/Bookmark

September 22, 2008 at 7:59 am | Car Parking Sensor, Front Parking Sensor, Parking Aids, Rear Parking Sensor, Reverse Parking | No comment

Tags: , , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/car-parking-sensor/vauxhall-car-reverse-parking-sensor-the-ultimate-universal-front-rear-car-parking-sensor/trackback/

TVR Car Reverse Parking Sensor – The Ultimate Front & Rear TVR Car Parking Sensor

Parking Dynamics PD1 TVR Parking & Reversing Sensors use a Unique, No Holes Design that is invisible when fitted. No Drill. No Holes. No Damage!

The TVR Parking Dynamics PD1 Reverse Parking Sensor uses a unique 100% Accurate, Responsive and Reliable Electromagnetic Sensor Technology that makes parking Safer and Easier, preventing Bumps, Scrapes and Nasty Bangs.

This reverse parking sensor technology is available as a Front and Rear reverse parking sensor giving your vehicle all round parking and reversing protection and giving you Total Parking and Reversing Confidence.

A TVR Reverse Parking sensor that fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs & Motor Homes gives you total flexibility and optimum compatibility. The PD1 Detects all objects including People, Vehicles, Small & High Kerbs, Pillars, Posts, Walls, Fences, Barriers, Garage Doors, Skips, etc.

As recently reported by the insurance industry, 27% of vehicle accidents are now caused by driver error, when parking and reversing! With more cars on the road now than ever before, the Risk is even greater for accidents to occur. The TVR Parking Dynamics PD1 will give you peace-of-mind and total parking confidence.

Unique Design:

This unique adhesive metallic antenna design mounts discretely on the inner side of your plastic bumper preserving the ‘new factory look’ of your vehicle and maintains the sleek aesthetic lines of today’s prestige vehicles. Far superior in design and performance to the ultrasonic type of sensor that has ugly and visible sensors.

Totally unique in design, the TVR PD1 reverse parking sensor is a superior alternative to the older ultrasonic type sensor technology that requires you to drill 4 or 6 holes in your bumper, mounting ugly black sensors that then need painting to colour code and match the shade of your bumper… The Parking Dynamics PD1 makes this a thing of the past!

Find out more about the Parking Dynamics PD1 TVR Reverse Parking Sensor

 Technical Operation:

When reverse gear is selected the small control unit generates a magnetic field and transfers this to the transceiver adhesive strip that is placed on the inner side of and run the length of your bumper. The PD1 Front sensor is activated by a a switch and works in exactly the same way as the PD1 rear reverse sensor.

The magnetic strip then sends out an elliptical magnetic field to cover the full area around your bumper, front, rear and sides. The transceiver strip works by sending and receiving unlike ultrasonic parking and reverse sensors that require 2 types of sensors, one to send and one to receive; if they become dirty the ultrasonic performance can deteriorate.

Mass is then monitored by the control unit by translating this into a voltage. When an object (i.e. people, kerbs, cars, etc) heavier in mass than the magnetic field enters this elliptical zone, an increase in voltage is detected by the control unit and you are then informed by a series of TVRble tones or display (PD1-Vision only) how close you are to the object. You can then manoeuvre accordingly with plenty of time to react.

User Operation giving Full Bumper Coverage and Early Detection:

Using Electromagnetic Technology, the TVR PD1 reverse parking sensor will scan the full length of your bumper, from end to end picking up all objects behind your vehicle. The PD1 detects children, people, adults the elderly plus cars, vehicles, small kerbs, walls, barriers, pillars, posts, skips, etc. Whatever is behind you can rest assured the TVR PD1 will detect this object and alert you to its presence allowing you to react, with time to spare.

When reverse gear is engaged the reverse parking sensor system provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different TVRble tones (Zones) alerting you of your proximity in relation to surrounding objects!

As you reverse Zone 1 (furthest away from the object) picks up the object first.

Zone 1: 0.8 to 0.5 Metres in length – The 1st tone signals with a slow "be-be-be" sound

Zone 2: 0.5 to 0.25 Metres in length – The 2nd tone is a faster "be-be-be" sound

Zone 3: 0.25 to 0 Metres in length – the 3rd tone is a constant "beeeeeep" sound

 TVR Parking Dynamics PD1 Advantages Are Clear!

Parking Dynamics PD1 fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs and Motor Homes giving you maximum compatibility, functionality, reliability and high performance accuracy.

The PD1 is flexible and allows you to move the sensor from vehicle to vehicle upon resale, for the minimum cost of a replacement antenna. No bumper adjustments make this ideal for Rental and Leasing companies.

No Visible Parts, Period! The Parking Dynamics PD1 when fitted is a completely discrete and totally invisible. Only you will know it’s fitted. This ensures a no-holes installation, a higher value to your car—and a more desirable car.

Being CAN bus compatible ensures the PD1 integrates seamlessly with both older conventional wiring systems and the latest intelligent (CAN Bus) multiplex wiring systems. Connect the wrong aftermarket reverse parking sensor and it could be costly. Parking Dynamics is the solution to this dilemma!

No-Drill! The PD1 is fitted without drilling your bumper and unlike ultrasonic type parking sensors there are NO ugly sensors to be mounted in your bumper and then painted. No need to match the paint colour.

A Maintenance FREE Front and Rear parking and reverse sensor technology - No Cleaning, No Adjustment and No Painting of sensors or Constant Testing required!

100% accurate, responsive and reliable in all parking situations and weather conditions – Regardless of the conditions: Sun, Rain, Wind, Snow or Hail the PD1 works and gives you accurate feedback in real time, every time.

TVR Reverse Parking sensors help and result in a major decrease in minor damage collisions caused when parking and reversing. This simple device will pay for itself many times over by reducing the number of small bangs in which you are involved. Completely eliminating the chance of putting your No Claims Bonus at risk!

Find out more about the Parking Dynamics PD1 TVR Reverse Parking Sensor

 The TVR Reverse Parking Dynamics PD1 System comprises of the following!

- The Speaker is small and at just 20mm in diameter mounts anywhere inside of the vehicle and can be run to any location. The TVRble tones that are emitted to alert you of the proximity of surrounding objects can be clearly heard even when mounted at the back of the vehicle close to or behind interior panels.

- The Electronic Control Unit (ECU) is the ‘brain’ of the PD1, and mounts securely using the supplied adhesive strip either inside of the boot or behind the vehicle bumper. The front ECU mounts under the bonnet or inside of the car, typically behind the glove box. Dimensions of this compact rear sensor unit are just (L57mm x H13mm x D33mm) and the front sensor dimensions are (L75mm x H23mm x D40mm)

- The Antenna is a very strong and flexible adhesive metallic tape that mounts behind the bumper. Its 1cm height and 2.7m length gives you flexibility to run over bumper curves and round bumper mouldings and ensures 100% bumper coverage of even the largest vehicle, offering a full, all round protection zone. The antenna can be cut to any length in seconds.

- The Switch included with the PD1-Front only, mounts discretely inside of the vehicle typically under the steering wheel area for easy access. Press the push-button switch to activate the PD1-Front when parking.

- The LED Display included with the PD1-Vision only, mounts discretely on the rear view mirror and gives you visual and TVRble alerts to inform you of the proximity of surrounding objects. LED Display Dimensions (L90mm x H30mm x D12mm)

 TVR Reverse Parking Dynamics PD1 Features:

  • 100% Discrete! No visible parts, so only you will know it is fitted.
  • Automatically beeps if you get to close to an object.
  • Detects people, vehicles, small & high kerbs, garage doors, pillars, posts, walls, fences, barriers, skips, etc.
  • Scans & Protects full length of bumper even onto sides unlike ultrasonic’s.
  • Maintenance FREE!
  • No-Drill, No-Damage! Fitted without drilling bumper unlike ultrasonic type parking sensors.
  • 100% accurate, reliable and responsive in all parking situations and weather conditions.
  • No Paint Required! Unlike ultrasonic type sensors.
  • 2.7 Metre Adhesive antenna mounts on inner side of bumper and can be cut to fit any size of bumper.
  • 100% Compatible with both conventional and the latest CAN Bus multiplex wiring systems.
  • 3 TVRble Tones alert you of your proximity in relation to surrounding objects. PD1 Vision also has a display.
  • Easy 3 wire installation.
  • Compatible with vehicles that have a tow bar fitted or spare wheel fixed to rear door.
  • Fits all vehicles with a plastic bumper including Cars, 4×4, MPV, SUV, Vans, Vehicles, Motor homes.
  • Ideal for Rental and Leasing companies as no bumper adjustments are required.
  • 2 Year Guarantee.
  • High Performance Reverse Parking Sensor, Reverse Sensor, Reversing Sensor, Parking Aid!

Find out more about the Parking Dynamics PD1 TVR Reverse Parking Sensor

  • Share/Bookmark

September 22, 2008 at 7:49 am | Car Parking Sensor, Front Parking Sensor, Parking Aids, Rear Parking Sensor, Reverse Parking | No comment

Tags: , , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/car-parking-sensor/tvr-car-reverse-parking-sensor-the-ultimate-universal-front-rear-car-parking-sensor/trackback/

Toyota Car Reverse Parking Sensor – The Ultimate Front & Rear Toyota Car Parking Sensor

Parking Dynamics PD1 Toyota Parking & Reversing Sensors use a Unique, No Holes Design that is invisible when fitted. No Drill. No Holes. No Damage!

The Toyota Parking Dynamics PD1 Reverse Parking Sensor uses a unique 100% Accurate, Responsive and Reliable Electromagnetic Sensor Technology that makes parking Safer and Easier, preventing Bumps, Scrapes and Nasty Bangs.

This reverse parking sensor technology is available as a Front and Rear reverse parking sensor giving your vehicle all round parking and reversing protection and giving you Total Parking and Reversing Confidence.

A Toyota Reverse Parking sensor that fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs & Motor Homes gives you total flexibility and optimum compatibility. The PD1 Detects all objects including People, Vehicles, Small & High Kerbs, Pillars, Posts, Walls, Fences, Barriers, Garage Doors, Skips, etc.

As recently reported by the insurance industry, 27% of vehicle accidents are now caused by driver error, when parking and reversing! With more cars on the road now than ever before, the Risk is even greater for accidents to occur. The Toyota Parking Dynamics PD1 will give you peace-of-mind and total parking confidence.

Unique Design:

This unique adhesive metallic antenna design mounts discretely on the inner side of your plastic bumper preserving the ‘new factory look’ of your vehicle and maintains the sleek aesthetic lines of today’s prestige vehicles. Far superior in design and performance to the ultrasonic type of sensor that has ugly and visible sensors.

Totally unique in design, the Toyota PD1 reverse parking sensor is a superior alternative to the older ultrasonic type sensor technology that requires you to drill 4 or 6 holes in your bumper, mounting ugly black sensors that then need painting to colour code and match the shade of your bumper… The Parking Dynamics PD1 makes this a thing of the past!

Find out more about the Parking Dynamics PD1 Toyota Reverse Parking Sensor

 Technical Operation:

When reverse gear is selected the small control unit generates a magnetic field and transfers this to the transceiver adhesive strip that is placed on the inner side of and run the length of your bumper. The PD1 Front sensor is activated by a a switch and works in exactly the same way as the PD1 rear reverse sensor.

The magnetic strip then sends out an elliptical magnetic field to cover the full area around your bumper, front, rear and sides. The transceiver strip works by sending and receiving unlike ultrasonic parking and reverse sensors that require 2 types of sensors, one to send and one to receive; if they become dirty the ultrasonic performance can deteriorate.

Mass is then monitored by the control unit by translating this into a voltage. When an object (i.e. people, kerbs, cars, etc) heavier in mass than the magnetic field enters this elliptical zone, an increase in voltage is detected by the control unit and you are then informed by a series of Toyotable tones or display (PD1-Vision only) how close you are to the object. You can then manoeuvre accordingly with plenty of time to react.

User Operation giving Full Bumper Coverage and Early Detection:

Using Electromagnetic Technology, the Toyota PD1 reverse parking sensor will scan the full length of your bumper, from end to end picking up all objects behind your vehicle. The PD1 detects children, people, adults the elderly plus cars, vehicles, small kerbs, walls, barriers, pillars, posts, skips, etc. Whatever is behind you can rest assured the Toyota PD1 will detect this object and alert you to its presence allowing you to react, with time to spare.

When reverse gear is engaged the reverse parking sensor system provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different Toyotable tones (Zones) alerting you of your proximity in relation to surrounding objects!

As you reverse Zone 1 (furthest away from the object) picks up the object first.

Zone 1: 0.8 to 0.5 Metres in length – The 1st tone signals with a slow "be-be-be" sound

Zone 2: 0.5 to 0.25 Metres in length – The 2nd tone is a faster "be-be-be" sound

Zone 3: 0.25 to 0 Metres in length – the 3rd tone is a constant "beeeeeep" sound

 Toyota Parking Dynamics PD1 Advantages Are Clear!

Parking Dynamics PD1 fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs and Motor Homes giving you maximum compatibility, functionality, reliability and high performance accuracy.

The PD1 is flexible and allows you to move the sensor from vehicle to vehicle upon resale, for the minimum cost of a replacement antenna. No bumper adjustments make this ideal for Rental and Leasing companies.

No Visible Parts, Period! The Parking Dynamics PD1 when fitted is a completely discrete and totally invisible. Only you will know it’s fitted. This ensures a no-holes installation, a higher value to your car—and a more desirable car.

Being CAN bus compatible ensures the PD1 integrates seamlessly with both older conventional wiring systems and the latest intelligent (CAN Bus) multiplex wiring systems. Connect the wrong aftermarket reverse parking sensor and it could be costly. Parking Dynamics is the solution to this dilemma!

No-Drill! The PD1 is fitted without drilling your bumper and unlike ultrasonic type parking sensors there are NO ugly sensors to be mounted in your bumper and then painted. No need to match the paint colour.

A Maintenance FREE Front and Rear parking and reverse sensor technology - No Cleaning, No Adjustment and No Painting of sensors or Constant Testing required!

100% accurate, responsive and reliable in all parking situations and weather conditions – Regardless of the conditions: Sun, Rain, Wind, Snow or Hail the PD1 works and gives you accurate feedback in real time, every time.

Toyota Reverse Parking sensors help and result in a major decrease in minor damage collisions caused when parking and reversing. This simple device will pay for itself many times over by reducing the number of small bangs in which you are involved. Completely eliminating the chance of putting your No Claims Bonus at risk!

Find out more about the Parking Dynamics PD1 Toyota Reverse Parking Sensor

 The Toyota Reverse Parking Dynamics PD1 System comprises of the following!

- The Speaker is small and at just 20mm in diameter mounts anywhere inside of the vehicle and can be run to any location. The Toyotable tones that are emitted to alert you of the proximity of surrounding objects can be clearly heard even when mounted at the back of the vehicle close to or behind interior panels.

- The Electronic Control Unit (ECU) is the ‘brain’ of the PD1, and mounts securely using the supplied adhesive strip either inside of the boot or behind the vehicle bumper. The front ECU mounts under the bonnet or inside of the car, typically behind the glove box. Dimensions of this compact rear sensor unit are just (L57mm x H13mm x D33mm) and the front sensor dimensions are (L75mm x H23mm x D40mm)

- The Antenna is a very strong and flexible adhesive metallic tape that mounts behind the bumper. Its 1cm height and 2.7m length gives you flexibility to run over bumper curves and round bumper mouldings and ensures 100% bumper coverage of even the largest vehicle, offering a full, all round protection zone. The antenna can be cut to any length in seconds.

- The Switch included with the PD1-Front only, mounts discretely inside of the vehicle typically under the steering wheel area for easy access. Press the push-button switch to activate the PD1-Front when parking.

- The LED Display included with the PD1-Vision only, mounts discretely on the rear view mirror and gives you visual and Toyotable alerts to inform you of the proximity of surrounding objects. LED Display Dimensions (L90mm x H30mm x D12mm)

 Toyota Reverse Parking Dynamics PD1 Features:

  • 100% Discrete! No visible parts, so only you will know it is fitted.
  • Automatically beeps if you get to close to an object.
  • Detects people, vehicles, small & high kerbs, garage doors, pillars, posts, walls, fences, barriers, skips, etc.
  • Scans & Protects full length of bumper even onto sides unlike ultrasonic’s.
  • Maintenance FREE!
  • No-Drill, No-Damage! Fitted without drilling bumper unlike ultrasonic type parking sensors.
  • 100% accurate, reliable and responsive in all parking situations and weather conditions.
  • No Paint Required! Unlike ultrasonic type sensors.
  • 2.7 Metre Adhesive antenna mounts on inner side of bumper and can be cut to fit any size of bumper.
  • 100% Compatible with both conventional and the latest CAN Bus multiplex wiring systems.
  • 3 Toyotable Tones alert you of your proximity in relation to surrounding objects. PD1 Vision also has a display.
  • Easy 3 wire installation.
  • Compatible with vehicles that have a tow bar fitted or spare wheel fixed to rear door.
  • Fits all vehicles with a plastic bumper including Cars, 4×4, MPV, SUV, Vans, Vehicles, Motor homes.
  • Ideal for Rental and Leasing companies as no bumper adjustments are required.
  • 2 Year Guarantee.
  • High Performance Reverse Parking Sensor, Reverse Sensor, Reversing Sensor, Parking Aid!

Find out more about the Parking Dynamics PD1 Toyota Reverse Parking Sensor

  • Share/Bookmark

September 22, 2008 at 7:42 am | Car Parking Sensor, Front Parking Sensor, Parking Aids, Rear Parking Sensor, Reverse Parking | No comment

Tags: , , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/car-parking-sensor/toyota-car-reverse-parking-sensor-the-ultimate-universal-front-rear-car-parking-sensor/trackback/

Suzuki Car Reverse Parking Sensor – The Ultimate Front & Rear Suzuki Car Parking Sensor

Parking Dynamics PD1 Suzuki Parking & Reversing Sensors use a Unique, No Holes Design that is invisible when fitted. No Drill. No Holes. No Damage!

The Suzuki Parking Dynamics PD1 Reverse Parking Sensor uses a unique 100% Accurate, Responsive and Reliable Electromagnetic Sensor Technology that makes parking Safer and Easier, preventing Bumps, Scrapes and Nasty Bangs.

This reverse parking sensor technology is available as a Front and Rear reverse parking sensor giving your vehicle all round parking and reversing protection and giving you Total Parking and Reversing Confidence.

A Suzuki Reverse Parking sensor that fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs & Motor Homes gives you total flexibility and optimum compatibility. The PD1 Detects all objects including People, Vehicles, Small & High Kerbs, Pillars, Posts, Walls, Fences, Barriers, Garage Doors, Skips, etc.

As recently reported by the insurance industry, 27% of vehicle accidents are now caused by driver error, when parking and reversing! With more cars on the road now than ever before, the Risk is even greater for accidents to occur. The Suzuki Parking Dynamics PD1 will give you peace-of-mind and total parking confidence.

Unique Design:

This unique adhesive metallic antenna design mounts discretely on the inner side of your plastic bumper preserving the ‘new factory look’ of your vehicle and maintains the sleek aesthetic lines of today’s prestige vehicles. Far superior in design and performance to the ultrasonic type of sensor that has ugly and visible sensors.

Totally unique in design, the Suzuki PD1 reverse parking sensor is a superior alternative to the older ultrasonic type sensor technology that requires you to drill 4 or 6 holes in your bumper, mounting ugly black sensors that then need painting to colour code and match the shade of your bumper… The Parking Dynamics PD1 makes this a thing of the past!

Find out more about the Parking Dynamics PD1 Suzuki Reverse Parking Sensor

 Technical Operation:

When reverse gear is selected the small control unit generates a magnetic field and transfers this to the transceiver adhesive strip that is placed on the inner side of and run the length of your bumper. The PD1 Front sensor is activated by a a switch and works in exactly the same way as the PD1 rear reverse sensor.

The magnetic strip then sends out an elliptical magnetic field to cover the full area around your bumper, front, rear and sides. The transceiver strip works by sending and receiving unlike ultrasonic parking and reverse sensors that require 2 types of sensors, one to send and one to receive; if they become dirty the ultrasonic performance can deteriorate.

Mass is then monitored by the control unit by translating this into a voltage. When an object (i.e. people, kerbs, cars, etc) heavier in mass than the magnetic field enters this elliptical zone, an increase in voltage is detected by the control unit and you are then informed by a series of Suzukible tones or display (PD1-Vision only) how close you are to the object. You can then manoeuvre accordingly with plenty of time to react.

User Operation giving Full Bumper Coverage and Early Detection:

Using Electromagnetic Technology, the Suzuki PD1 reverse parking sensor will scan the full length of your bumper, from end to end picking up all objects behind your vehicle. The PD1 detects children, people, adults the elderly plus cars, vehicles, small kerbs, walls, barriers, pillars, posts, skips, etc. Whatever is behind you can rest assured the Suzuki PD1 will detect this object and alert you to its presence allowing you to react, with time to spare.

When reverse gear is engaged the reverse parking sensor system provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different Suzukible tones (Zones) alerting you of your proximity in relation to surrounding objects!

As you reverse Zone 1 (furthest away from the object) picks up the object first.

Zone 1: 0.8 to 0.5 Metres in length – The 1st tone signals with a slow "be-be-be" sound

Zone 2: 0.5 to 0.25 Metres in length – The 2nd tone is a faster "be-be-be" sound

Zone 3: 0.25 to 0 Metres in length – the 3rd tone is a constant "beeeeeep" sound

 Suzuki Parking Dynamics PD1 Advantages Are Clear!

Parking Dynamics PD1 fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs and Motor Homes giving you maximum compatibility, functionality, reliability and high performance accuracy.

The PD1 is flexible and allows you to move the sensor from vehicle to vehicle upon resale, for the minimum cost of a replacement antenna. No bumper adjustments make this ideal for Rental and Leasing companies.

No Visible Parts, Period! The Parking Dynamics PD1 when fitted is a completely discrete and totally invisible. Only you will know it’s fitted. This ensures a no-holes installation, a higher value to your car—and a more desirable car.

Being CAN bus compatible ensures the PD1 integrates seamlessly with both older conventional wiring systems and the latest intelligent (CAN Bus) multiplex wiring systems. Connect the wrong aftermarket reverse parking sensor and it could be costly. Parking Dynamics is the solution to this dilemma!

No-Drill! The PD1 is fitted without drilling your bumper and unlike ultrasonic type parking sensors there are NO ugly sensors to be mounted in your bumper and then painted. No need to match the paint colour.

A Maintenance FREE Front and Rear parking and reverse sensor technology - No Cleaning, No Adjustment and No Painting of sensors or Constant Testing required!

100% accurate, responsive and reliable in all parking situations and weather conditions – Regardless of the conditions: Sun, Rain, Wind, Snow or Hail the PD1 works and gives you accurate feedback in real time, every time.

Suzuki Reverse Parking sensors help and result in a major decrease in minor damage collisions caused when parking and reversing. This simple device will pay for itself many times over by reducing the number of small bangs in which you are involved. Completely eliminating the chance of putting your No Claims Bonus at risk!

Find out more about the Parking Dynamics PD1 Suzuki Reverse Parking Sensor

The Suzuki Reverse Parking Dynamics PD1 System comprises of the following!

- The Speaker is small and at just 20mm in diameter mounts anywhere inside of the vehicle and can be run to any location. The Suzukible tones that are emitted to alert you of the proximity of surrounding objects can be clearly heard even when mounted at the back of the vehicle close to or behind interior panels.

- The Electronic Control Unit (ECU) is the ‘brain’ of the PD1, and mounts securely using the supplied adhesive strip either inside of the boot or behind the vehicle bumper. The front ECU mounts under the bonnet or inside of the car, typically behind the glove box. Dimensions of this compact rear sensor unit are just (L57mm x H13mm x D33mm) and the front sensor dimensions are (L75mm x H23mm x D40mm)

- The Antenna is a very strong and flexible adhesive metallic tape that mounts behind the bumper. Its 1cm height and 2.7m length gives you flexibility to run over bumper curves and round bumper mouldings and ensures 100% bumper coverage of even the largest vehicle, offering a full, all round protection zone. The antenna can be cut to any length in seconds.

- The Switch included with the PD1-Front only, mounts discretely inside of the vehicle typically under the steering wheel area for easy access. Press the push-button switch to activate the PD1-Front when parking.

- The LED Display included with the PD1-Vision only, mounts discretely on the rear view mirror and gives you visual and Suzukible alerts to inform you of the proximity of surrounding objects. LED Display Dimensions (L90mm x H30mm x D12mm)

 Suzuki Reverse Parking Dynamics PD1 Features:

  • 100% Discrete! No visible parts, so only you will know it is fitted.
  • Automatically beeps if you get to close to an object.
  • Detects people, vehicles, small & high kerbs, garage doors, pillars, posts, walls, fences, barriers, skips, etc.
  • Scans & Protects full length of bumper even onto sides unlike ultrasonic’s.
  • Maintenance FREE!
  • No-Drill, No-Damage! Fitted without drilling bumper unlike ultrasonic type parking sensors.
  • 100% accurate, reliable and responsive in all parking situations and weather conditions.
  • No Paint Required! Unlike ultrasonic type sensors.
  • 2.7 Metre Adhesive antenna mounts on inner side of bumper and can be cut to fit any size of bumper.
  • 100% Compatible with both conventional and the latest CAN Bus multiplex wiring systems.
  • 3 Suzukible Tones alert you of your proximity in relation to surrounding objects. PD1 Vision also has a display.
  • Easy 3 wire installation.
  • Compatible with vehicles that have a tow bar fitted or spare wheel fixed to rear door.
  • Fits all vehicles with a plastic bumper including Cars, 4×4, MPV, SUV, Vans, Vehicles, Motor homes.
  • Ideal for Rental and Leasing companies as no bumper adjustments are required.
  • 2 Year Guarantee.
  • High Performance Reverse Parking Sensor, Reverse Sensor, Reversing Sensor, Parking Aid!

Find out more about the Parking Dynamics PD1 Suzuki Reverse Parking Sensor

  • Share/Bookmark

September 22, 2008 at 7:35 am | Front Parking Sensor, Parking Aids, Rear Parking Sensor, Reverse Parking | No comment

Tags: , , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/reverse-parking/suzuki-car-reverse-parking-sensor-the-ultimate-universal-front-rear-car-parking-sensor/trackback/

Subaru Car Reverse Parking Sensor – The Ultimate Front & Rear Subaru Car Parking Sensor

Parking Dynamics PD1 Subaru Parking & Reversing Sensors use a Unique, No Holes Design that is invisible when fitted. No Drill. No Holes. No Damage!

The Subaru Parking Dynamics PD1 Reverse Parking Sensor uses a unique 100% Accurate, Responsive and Reliable Electromagnetic Sensor Technology that makes parking Safer and Easier, preventing Bumps, Scrapes and Nasty Bangs.

This reverse parking sensor technology is available as a Front and Rear reverse parking sensor giving your vehicle all round parking and reversing protection and giving you Total Parking and Reversing Confidence.

A Subaru Reverse Parking sensor that fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs & Motor Homes gives you total flexibility and optimum compatibility. The PD1 Detects all objects including People, Vehicles, Small & High Kerbs, Pillars, Posts, Walls, Fences, Barriers, Garage Doors, Skips, etc.

As recently reported by the insurance industry, 27% of vehicle accidents are now caused by driver error, when parking and reversing! With more cars on the road now than ever before, the Risk is even greater for accidents to occur. The Subaru Parking Dynamics PD1 will give you peace-of-mind and total parking confidence.

Unique Design:

This unique adhesive metallic antenna design mounts discretely on the inner side of your plastic bumper preserving the ‘new factory look’ of your vehicle and maintains the sleek aesthetic lines of today’s prestige vehicles. Far superior in design and performance to the ultrasonic type of sensor that has ugly and visible sensors.

Totally unique in design, the Subaru PD1 reverse parking sensor is a superior alternative to the older ultrasonic type sensor technology that requires you to drill 4 or 6 holes in your bumper, mounting ugly black sensors that then need painting to colour code and match the shade of your bumper… The Parking Dynamics PD1 makes this a thing of the past!

Find out more about the Parking Dynamics PD1 Subaru Reverse Parking Sensor

 Technical Operation:

When reverse gear is selected the small control unit generates a magnetic field and transfers this to the transceiver adhesive strip that is placed on the inner side of and run the length of your bumper. The PD1 Front sensor is activated by a a switch and works in exactly the same way as the PD1 rear reverse sensor.

The magnetic strip then sends out an elliptical magnetic field to cover the full area around your bumper, front, rear and sides. The transceiver strip works by sending and receiving unlike ultrasonic parking and reverse sensors that require 2 types of sensors, one to send and one to receive; if they become dirty the ultrasonic performance can deteriorate.

Mass is then monitored by the control unit by translating this into a voltage. When an object (i.e. people, kerbs, cars, etc) heavier in mass than the magnetic field enters this elliptical zone, an increase in voltage is detected by the control unit and you are then informed by a series of Subaruble tones or display (PD1-Vision only) how close you are to the object. You can then manoeuvre accordingly with plenty of time to react.

User Operation giving Full Bumper Coverage and Early Detection:

Using Electromagnetic Technology, the Subaru PD1 reverse parking sensor will scan the full length of your bumper, from end to end picking up all objects behind your vehicle. The PD1 detects children, people, adults the elderly plus cars, vehicles, small kerbs, walls, barriers, pillars, posts, skips, etc. Whatever is behind you can rest assured the Subaru PD1 will detect this object and alert you to its presence allowing you to react, with time to spare.

When reverse gear is engaged the reverse parking sensor system provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different Subaruble tones (Zones) alerting you of your proximity in relation to surrounding objects!

As you reverse Zone 1 (furthest away from the object) picks up the object first.

Zone 1: 0.8 to 0.5 Metres in length – The 1st tone signals with a slow "be-be-be" sound

Zone 2: 0.5 to 0.25 Metres in length – The 2nd tone is a faster "be-be-be" sound

Zone 3: 0.25 to 0 Metres in length – the 3rd tone is a constant "beeeeeep" sound

 Subaru Parking Dynamics PD1 Advantages Are Clear!

Parking Dynamics PD1 fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs and Motor Homes giving you maximum compatibility, functionality, reliability and high performance accuracy.

The PD1 is flexible and allows you to move the sensor from vehicle to vehicle upon resale, for the minimum cost of a replacement antenna. No bumper adjustments make this ideal for Rental and Leasing companies.

No Visible Parts, Period! The Parking Dynamics PD1 when fitted is a completely discrete and totally invisible. Only you will know it’s fitted. This ensures a no-holes installation, a higher value to your car—and a more desirable car.

Being CAN bus compatible ensures the PD1 integrates seamlessly with both older conventional wiring systems and the latest intelligent (CAN Bus) multiplex wiring systems. Connect the wrong aftermarket reverse parking sensor and it could be costly. Parking Dynamics is the solution to this dilemma!

No-Drill! The PD1 is fitted without drilling your bumper and unlike ultrasonic type parking sensors there are NO ugly sensors to be mounted in your bumper and then painted. No need to match the paint colour.

A Maintenance FREE Front and Rear parking and reverse sensor technology - No Cleaning, No Adjustment and No Painting of sensors or Constant Testing required!

100% accurate, responsive and reliable in all parking situations and weather conditions – Regardless of the conditions: Sun, Rain, Wind, Snow or Hail the PD1 works and gives you accurate feedback in real time, every time.

Subaru Reverse Parking sensors help and result in a major decrease in minor damage collisions caused when parking and reversing. This simple device will pay for itself many times over by reducing the number of small bangs in which you are involved. Completely eliminating the chance of putting your No Claims Bonus at risk!

Find out more about the Parking Dynamics PD1 Subaru Reverse Parking Sensor

 The Subaru Reverse Parking Dynamics PD1 System comprises of the following!

- The Speaker is small and at just 20mm in diameter mounts anywhere inside of the vehicle and can be run to any location. The Subaruble tones that are emitted to alert you of the proximity of surrounding objects can be clearly heard even when mounted at the back of the vehicle close to or behind interior panels.

- The Electronic Control Unit (ECU) is the ‘brain’ of the PD1, and mounts securely using the supplied adhesive strip either inside of the boot or behind the vehicle bumper. The front ECU mounts under the bonnet or inside of the car, typically behind the glove box. Dimensions of this compact rear sensor unit are just (L57mm x H13mm x D33mm) and the front sensor dimensions are (L75mm x H23mm x D40mm)

- The Antenna is a very strong and flexible adhesive metallic tape that mounts behind the bumper. Its 1cm height and 2.7m length gives you flexibility to run over bumper curves and round bumper mouldings and ensures 100% bumper coverage of even the largest vehicle, offering a full, all round protection zone. The antenna can be cut to any length in seconds.

- The Switch included with the PD1-Front only, mounts discretely inside of the vehicle typically under the steering wheel area for easy access. Press the push-button switch to activate the PD1-Front when parking.

- The LED Display included with the PD1-Vision only, mounts discretely on the rear view mirror and gives you visual and Subaruble alerts to inform you of the proximity of surrounding objects. LED Display Dimensions (L90mm x H30mm x D12mm)

 Subaru Reverse Parking Dynamics PD1 Features:

  • 100% Discrete! No visible parts, so only you will know it is fitted.
  • Automatically beeps if you get to close to an object.
  • Detects people, vehicles, small & high kerbs, garage doors, pillars, posts, walls, fences, barriers, skips, etc.
  • Scans & Protects full length of bumper even onto sides unlike ultrasonic’s.
  • Maintenance FREE!
  • No-Drill, No-Damage! Fitted without drilling bumper unlike ultrasonic type parking sensors.
  • 100% accurate, reliable and responsive in all parking situations and weather conditions.
  • No Paint Required! Unlike ultrasonic type sensors.
  • 2.7 Metre Adhesive antenna mounts on inner side of bumper and can be cut to fit any size of bumper.
  • 100% Compatible with both conventional and the latest CAN Bus multiplex wiring systems.
  • 3 Subaruble Tones alert you of your proximity in relation to surrounding objects. PD1 Vision also has a display.
  • Easy 3 wire installation.
  • Compatible with vehicles that have a tow bar fitted or spare wheel fixed to rear door.
  • Fits all vehicles with a plastic bumper including Cars, 4×4, MPV, SUV, Vans, Vehicles, Motor homes.
  • Ideal for Rental and Leasing companies as no bumper adjustments are required.
  • 2 Year Guarantee.
  • High Performance Reverse Parking Sensor, Reverse Sensor, Reversing Sensor, Parking Aid!

Find out more about the Parking Dynamics PD1 Subaru Reverse Parking Sensor

  • Share/Bookmark

September 22, 2008 at 7:30 am | Car Parking Sensor, Front Parking Sensor, Parking Aids, Rear Parking Sensor, Reverse Parking | No comment

Tags: , , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/car-parking-sensor/subaru-car-reverse-parking-sensor-the-ultimate-universal-front-rear-car-parking-sensor/trackback/

SsangYong Car Reverse Parking Sensor – The Ultimate Front & Rear SsangYong Car Parking Sensor

Parking Dynamics PD1 SsangYong Parking & Reversing Sensors use a Unique, No Holes Design that is invisible when fitted. No Drill. No Holes. No Damage!

The SsangYong Parking Dynamics PD1 Reverse Parking Sensor uses a unique 100% Accurate, Responsive and Reliable Electromagnetic Sensor Technology that makes parking Safer and Easier, preventing Bumps, Scrapes and Nasty Bangs.

This reverse parking sensor technology is available as a Front and Rear reverse parking sensor giving your vehicle all round parking and reversing protection and giving you Total Parking and Reversing Confidence.

A SsangYong Reverse Parking sensor that fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs & Motor Homes gives you total flexibility and optimum compatibility. The PD1 Detects all objects including People, Vehicles, Small & High Kerbs, Pillars, Posts, Walls, Fences, Barriers, Garage Doors, Skips, etc.

As recently reported by the insurance industry, 27% of vehicle accidents are now caused by driver error, when parking and reversing! With more cars on the road now than ever before, the Risk is even greater for accidents to occur. The SsangYong Parking Dynamics PD1 will give you peace-of-mind and total parking confidence.

Unique Design:

This unique adhesive metallic antenna design mounts discretely on the inner side of your plastic bumper preserving the ‘new factory look’ of your vehicle and maintains the sleek aesthetic lines of today’s prestige vehicles. Far superior in design and performance to the ultrasonic type of sensor that has ugly and visible sensors.

Totally unique in design, the SsangYong PD1 reverse parking sensor is a superior alternative to the older ultrasonic type sensor technology that requires you to drill 4 or 6 holes in your bumper, mounting ugly black sensors that then need painting to colour code and match the shade of your bumper… The Parking Dynamics PD1 makes this a thing of the past!

Find out more about the Parking Dynamics PD1 SsangYong Reverse Parking Sensor

 Technical Operation:

When reverse gear is selected the small control unit generates a magnetic field and transfers this to the transceiver adhesive strip that is placed on the inner side of and run the length of your bumper. The PD1 Front sensor is activated by a a switch and works in exactly the same way as the PD1 rear reverse sensor.

The magnetic strip then sends out an elliptical magnetic field to cover the full area around your bumper, front, rear and sides. The transceiver strip works by sending and receiving unlike ultrasonic parking and reverse sensors that require 2 types of sensors, one to send and one to receive; if they become dirty the ultrasonic performance can deteriorate.

Mass is then monitored by the control unit by translating this into a voltage. When an object (i.e. people, kerbs, cars, etc) heavier in mass than the magnetic field enters this elliptical zone, an increase in voltage is detected by the control unit and you are then informed by a series of SsangYongble tones or display (PD1-Vision only) how close you are to the object. You can then manoeuvre accordingly with plenty of time to react.

User Operation giving Full Bumper Coverage and Early Detection:

Using Electromagnetic Technology, the SsangYong PD1 reverse parking sensor will scan the full length of your bumper, from end to end picking up all objects behind your vehicle. The PD1 detects children, people, adults the elderly plus cars, vehicles, small kerbs, walls, barriers, pillars, posts, skips, etc. Whatever is behind you can rest assured the SsangYong PD1 will detect this object and alert you to its presence allowing you to react, with time to spare.

When reverse gear is engaged the reverse parking sensor system provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different SsangYongble tones (Zones) alerting you of your proximity in relation to surrounding objects!

As you reverse Zone 1 (furthest away from the object) picks up the object first.

Zone 1: 0.8 to 0.5 Metres in length – The 1st tone signals with a slow "be-be-be" sound

Zone 2: 0.5 to 0.25 Metres in length – The 2nd tone is a faster "be-be-be" sound

Zone 3: 0.25 to 0 Metres in length – the 3rd tone is a constant "beeeeeep" sound

 SsangYong Parking Dynamics PD1 Advantages Are Clear!

Parking Dynamics PD1 fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs and Motor Homes giving you maximum compatibility, functionality, reliability and high performance accuracy.

The PD1 is flexible and allows you to move the sensor from vehicle to vehicle upon resale, for the minimum cost of a replacement antenna. No bumper adjustments make this ideal for Rental and Leasing companies.

No Visible Parts, Period! The Parking Dynamics PD1 when fitted is a completely discrete and totally invisible. Only you will know it’s fitted. This ensures a no-holes installation, a higher value to your car—and a more desirable car.

Being CAN bus compatible ensures the PD1 integrates seamlessly with both older conventional wiring systems and the latest intelligent (CAN Bus) multiplex wiring systems. Connect the wrong aftermarket reverse parking sensor and it could be costly. Parking Dynamics is the solution to this dilemma!

No-Drill! The PD1 is fitted without drilling your bumper and unlike ultrasonic type parking sensors there are NO ugly sensors to be mounted in your bumper and then painted. No need to match the paint colour.

A Maintenance FREE Front and Rear parking and reverse sensor technology - No Cleaning, No Adjustment and No Painting of sensors or Constant Testing required!

100% accurate, responsive and reliable in all parking situations and weather conditions – Regardless of the conditions: Sun, Rain, Wind, Snow or Hail the PD1 works and gives you accurate feedback in real time, every time.

SsangYong Reverse Parking sensors help and result in a major decrease in minor damage collisions caused when parking and reversing. This simple device will pay for itself many times over by reducing the number of small bangs in which you are involved. Completely eliminating the chance of putting your No Claims Bonus at risk!

Find out more about the Parking Dynamics PD1 SsangYong Reverse Parking Sensor

 The SsangYong Reverse Parking Dynamics PD1 System comprises of the following!

- The Speaker is small and at just 20mm in diameter mounts anywhere inside of the vehicle and can be run to any location. The SsangYongble tones that are emitted to alert you of the proximity of surrounding objects can be clearly heard even when mounted at the back of the vehicle close to or behind interior panels.

- The Electronic Control Unit (ECU) is the ‘brain’ of the PD1, and mounts securely using the supplied adhesive strip either inside of the boot or behind the vehicle bumper. The front ECU mounts under the bonnet or inside of the car, typically behind the glove box. Dimensions of this compact rear sensor unit are just (L57mm x H13mm x D33mm) and the front sensor dimensions are (L75mm x H23mm x D40mm)

- The Antenna is a very strong and flexible adhesive metallic tape that mounts behind the bumper. Its 1cm height and 2.7m length gives you flexibility to run over bumper curves and round bumper mouldings and ensures 100% bumper coverage of even the largest vehicle, offering a full, all round protection zone. The antenna can be cut to any length in seconds.

- The Switch included with the PD1-Front only, mounts discretely inside of the vehicle typically under the steering wheel area for easy access. Press the push-button switch to activate the PD1-Front when parking.

- The LED Display included with the PD1-Vision only, mounts discretely on the rear view mirror and gives you visual and SsangYongble alerts to inform you of the proximity of surrounding objects. LED Display Dimensions (L90mm x H30mm x D12mm)

 SsangYong Reverse Parking Dynamics PD1 Features:

  • 100% Discrete! No visible parts, so only you will know it is fitted.
  • Automatically beeps if you get to close to an object.
  • Detects people, vehicles, small & high kerbs, garage doors, pillars, posts, walls, fences, barriers, skips, etc.
  • Scans & Protects full length of bumper even onto sides unlike ultrasonic’s.
  • Maintenance FREE!
  • No-Drill, No-Damage! Fitted without drilling bumper unlike ultrasonic type parking sensors.
  • 100% accurate, reliable and responsive in all parking situations and weather conditions.
  • No Paint Required! Unlike ultrasonic type sensors.
  • 2.7 Metre Adhesive antenna mounts on inner side of bumper and can be cut to fit any size of bumper.
  • 100% Compatible with both conventional and the latest CAN Bus multiplex wiring systems.
  • 3 SsangYongble Tones alert you of your proximity in relation to surrounding objects. PD1 Vision also has a display.
  • Easy 3 wire installation.
  • Compatible with vehicles that have a tow bar fitted or spare wheel fixed to rear door.
  • Fits all vehicles with a plastic bumper including Cars, 4×4, MPV, SUV, Vans, Vehicles, Motor homes.
  • Ideal for Rental and Leasing companies as no bumper adjustments are required.
  • 2 Year Guarantee.
  • High Performance Reverse Parking Sensor, Reverse Sensor, Reversing Sensor, Parking Aid!

Find out more about the Parking Dynamics PD1 SsangYong Reverse Parking Sensor

  • Share/Bookmark

September 22, 2008 at 7:22 am | Car Parking Sensor, Front Parking Sensor, Parking Aids, Rear Parking Sensor, Reverse Parking | No comment

Tags: , , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/car-parking-sensor/ssangyong-car-reverse-parking-sensor-the-ultimate-universal-front-rear-car-parking-sensor/trackback/

Smart Car Reverse Parking Sensor – The Ultimate Front & Rear Smart Car Parking Sensor

Parking Dynamics PD1 Smart Parking & Reversing Sensors use a Unique, No Holes Design that is invisible when fitted. No Drill. No Holes. No Damage!

The Smart Parking Dynamics PD1 Reverse Parking Sensor uses a unique 100% Accurate, Responsive and Reliable Electromagnetic Sensor Technology that makes parking Safer and Easier, preventing Bumps, Scrapes and Nasty Bangs.

This reverse parking sensor technology is available as a Front and Rear reverse parking sensor giving your vehicle all round parking and reversing protection and giving you Total Parking and Reversing Confidence.

A Smart Reverse Parking sensor that fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs & Motor Homes gives you total flexibility and optimum compatibility. The PD1 Detects all objects including People, Vehicles, Small & High Kerbs, Pillars, Posts, Walls, Fences, Barriers, Garage Doors, Skips, etc.

As recently reported by the insurance industry, 27% of vehicle accidents are now caused by driver error, when parking and reversing! With more cars on the road now than ever before, the Risk is even greater for accidents to occur. The Smart Parking Dynamics PD1 will give you peace-of-mind and total parking confidence.

Unique Design:

This unique adhesive metallic antenna design mounts discretely on the inner side of your plastic bumper preserving the ‘new factory look’ of your vehicle and maintains the sleek aesthetic lines of today’s prestige vehicles. Far superior in design and performance to the ultrasonic type of sensor that has ugly and visible sensors.

Totally unique in design, the Smart PD1 reverse parking sensor is a superior alternative to the older ultrasonic type sensor technology that requires you to drill 4 or 6 holes in your bumper, mounting ugly black sensors that then need painting to colour code and match the shade of your bumper… The Parking Dynamics PD1 makes this a thing of the past!

Find out more about the Parking Dynamics PD1 Smart Reverse Parking Sensor

 Technical Operation:

When reverse gear is selected the small control unit generates a magnetic field and transfers this to the transceiver adhesive strip that is placed on the inner side of and run the length of your bumper. The PD1 Front sensor is activated by a a switch and works in exactly the same way as the PD1 rear reverse sensor.

The magnetic strip then sends out an elliptical magnetic field to cover the full area around your bumper, front, rear and sides. The transceiver strip works by sending and receiving unlike ultrasonic parking and reverse sensors that require 2 types of sensors, one to send and one to receive; if they become dirty the ultrasonic performance can deteriorate.

Mass is then monitored by the control unit by translating this into a voltage. When an object (i.e. people, kerbs, cars, etc) heavier in mass than the magnetic field enters this elliptical zone, an increase in voltage is detected by the control unit and you are then informed by a series of Smartble tones or display (PD1-Vision only) how close you are to the object. You can then manoeuvre accordingly with plenty of time to react.

User Operation giving Full Bumper Coverage and Early Detection:

Using Electromagnetic Technology, the Smart PD1 reverse parking sensor will scan the full length of your bumper, from end to end picking up all objects behind your vehicle. The PD1 detects children, people, adults the elderly plus cars, vehicles, small kerbs, walls, barriers, pillars, posts, skips, etc. Whatever is behind you can rest assured the Smart PD1 will detect this object and alert you to its presence allowing you to react, with time to spare.

When reverse gear is engaged the reverse parking sensor system provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different Smartble tones (Zones) alerting you of your proximity in relation to surrounding objects!

As you reverse Zone 1 (furthest away from the object) picks up the object first.

Zone 1: 0.8 to 0.5 Metres in length – The 1st tone signals with a slow "be-be-be" sound

Zone 2: 0.5 to 0.25 Metres in length – The 2nd tone is a faster "be-be-be" sound

Zone 3: 0.25 to 0 Metres in length – the 3rd tone is a constant "beeeeeep" sound

 Smart Parking Dynamics PD1 Advantages Are Clear!

Parking Dynamics PD1 fits all Cars, Vehicles, Vans, 4×4s, MPVs, SUVs and Motor Homes giving you maximum compatibility, functionality, reliability and high performance accuracy.

The PD1 is flexible and allows you to move the sensor from vehicle to vehicle upon resale, for the minimum cost of a replacement antenna. No bumper adjustments make this ideal for Rental and Leasing companies.

No Visible Parts, Period! The Parking Dynamics PD1 when fitted is a completely discrete and totally invisible. Only you will know it’s fitted. This ensures a no-holes installation, a higher value to your car—and a more desirable car.

Being CAN bus compatible ensures the PD1 integrates seamlessly with both older conventional wiring systems and the latest intelligent (CAN Bus) multiplex wiring systems. Connect the wrong aftermarket reverse parking sensor and it could be costly. Parking Dynamics is the solution to this dilemma!

No-Drill! The PD1 is fitted without drilling your bumper and unlike ultrasonic type parking sensors there are NO ugly sensors to be mounted in your bumper and then painted. No need to match the paint colour.

A Maintenance FREE Front and Rear parking and reverse sensor technology - No Cleaning, No Adjustment and No Painting of sensors or Constant Testing required!

100% accurate, responsive and reliable in all parking situations and weather conditions – Regardless of the conditions: Sun, Rain, Wind, Snow or Hail the PD1 works and gives you accurate feedback in real time, every time.

Smart Reverse Parking sensors help and result in a major decrease in minor damage collisions caused when parking and reversing. This simple device will pay for itself many times over by reducing the number of small bangs in which you are involved. Completely eliminating the chance of putting your No Claims Bonus at risk!

Find out more about the Parking Dynamics PD1 Smart Reverse Parking Sensor

 The Smart Reverse Parking Dynamics PD1 System comprises of the following!

- The Speaker is small and at just 20mm in diameter mounts anywhere inside of the vehicle and can be run to any location. The Smartble tones that are emitted to alert you of the proximity of surrounding objects can be clearly heard even when mounted at the back of the vehicle close to or behind interior panels.

- The Electronic Control Unit (ECU) is the ‘brain’ of the PD1, and mounts securely using the supplied adhesive strip either inside of the boot or behind the vehicle bumper. The front ECU mounts under the bonnet or inside of the car, typically behind the glove box. Dimensions of this compact rear sensor unit are just (L57mm x H13mm x D33mm) and the front sensor dimensions are (L75mm x H23mm x D40mm)

- The Antenna is a very strong and flexible adhesive metallic tape that mounts behind the bumper. Its 1cm height and 2.7m length gives you flexibility to run over bumper curves and round bumper mouldings and ensures 100% bumper coverage of even the largest vehicle, offering a full, all round protection zone. The antenna can be cut to any length in seconds.

- The Switch included with the PD1-Front only, mounts discretely inside of the vehicle typically under the steering wheel area for easy access. Press the push-button switch to activate the PD1-Front when parking.

- The LED Display included with the PD1-Vision only, mounts discretely on the rear view mirror and gives you visual and Smartble alerts to inform you of the proximity of surrounding objects. LED Display Dimensions (L90mm x H30mm x D12mm)

 Smart Reverse Parking Dynamics PD1 Features:

  • 100% Discrete! No visible parts, so only you will know it is fitted.
  • Automatically beeps if you get to close to an object.
  • Detects people, vehicles, small & high kerbs, garage doors, pillars, posts, walls, fences, barriers, skips, etc.
  • Scans & Protects full length of bumper even onto sides unlike ultrasonic’s.
  • Maintenance FREE!
  • No-Drill, No-Damage! Fitted without drilling bumper unlike ultrasonic type parking sensors.
  • 100% accurate, reliable and responsive in all parking situations and weather conditions.
  • No Paint Required! Unlike ultrasonic type sensors.
  • 2.7 Metre Adhesive antenna mounts on inner side of bumper and can be cut to fit any size of bumper.
  • 100% Compatible with both conventional and the latest CAN Bus multiplex wiring systems.
  • 3 Smartble Tones alert you of your proximity in relation to surrounding objects. PD1 Vision also has a display.
  • Easy 3 wire installation.
  • Compatible with vehicles that have a tow bar fitted or spare wheel fixed to rear door.
  • Fits all vehicles with a plastic bumper including Cars, 4×4, MPV, SUV, Vans, Vehicles, Motor homes.
  • Ideal for Rental and Leasing companies as no bumper adjustments are required.
  • 2 Year Guarantee.
  • High Performance Reverse Parking Sensor, Reverse Sensor, Reversing Sensor, Parking Aid!

Find out more about the Parking Dynamics PD1 Smart Reverse Parking Sensor

  • Share/Bookmark

September 22, 2008 at 7:17 am | Car Parking Sensor, Front Parking Sensor, Parking Aids, Rear Parking Sensor, Reverse Parking | No comment

Tags: , , , , , ,

Trackback URL for this post:
http://www.parkingdynamics.co.uk/blog/car-parking-sensor/smart-car-reverse-parking-sensor-the-ultimate-universal-front-rear-car-parking-sensor/trackback/

Next Page »

Stay Up to Date

Subscribe to Parking Dynamics RSS Feed

Subscribe to Parking Dynamics RSS Feed.

Search Blog


Random Posts

Archives

Newsletter

Newsletter

Enter your name & email address below to get new parking tips, videos, latest news, discounts and much, much more..

Email:

First Name:

Entries (RSS)Entries (RSS)